A red light turns on while resetting: The earbuds are resetting.An orange and red light flashing: The earbuds have a low battery.Said red light turns off: The earbuds are fully charged.A red light on: The earbuds are charging.A blue light flashes: The earbuds are now connected.A blue and red light starts flashing: The earbuds will be ready to pair with any device.A blue light starts flashing: The earbuds turn on.Step 3: Press and hold the touch panel on both earbuds for about 20 seconds, or until a red light turns on. Step 2: Place both earbuds into the charging case and keep the lid open. Step 1: Delete all “ JBL Endurance Peak II” pairing records on the connected device. To charge the charging case, all you have to do is to connect the case to a USB charger or charging port with the included USB-A to C cable. The earbuds will start charging automatically. To charge the earbuds, all you have to do is to place them into the charging case and close the lid. To activate or deactivate the mono mode in these earbuds, all you have to do is to pair the earbuds to the device and take out one of the earbuds from the charging case. Activate the voice assistant: Press and hold the touch panel on any of the earbuds two times.Ĭredits: JBL How to Activate The Mono Mode?.Mute or unmute the microphone: Press and hold the touch panel on any of the earbuds.Play or pause a song: Press the touch panel on any of the earbuds one time.Activate the voice assistant: Press the touch panel on the right earbud one time.Mute or unmute the microphone: Press and hold the touch panel on any of the earbuds for about 2 seconds.Reject an incoming call: Press the touch panel on any of the earbuds two times.End a current call: Press the touch panel on any of the earbuds one time.Answer an incoming call: Press the touch panel on any of the earbuds one time.Play the previous song: Press the touch panel on the left earbud two times.Play the next song: Press the touch panel on the left earbud one time.Turn the volume down: Slide down the touch panel on the right earbud.Turn the volume up: Slide up the touch panel on the right earbud.Play or pause a song: Press the touch panel on the right earbud one time.Credits: JBL How to Control? / How to Operate? – Instructions After that, the earbuds will turn off automatically. Turn off: Place the earbuds into the charging case and close its lid. After that, a blue light will start flashing, and the earbuds will turn on automatically. Turn on: Open the lid of the charging case and take the earbuds out. ![]() Step 5: Rotate for the best possible comfort and best fit, and make sure that the microphone is pointing to the mouth. Step 4: Insert the headphones into the inner canal of the ears. Step 3: Choose the ear tips that best suit your ears. Step 2: Identify the left and right earbuds. Step 1: Take both earbuds out of the charging case. ![]() ![]() When a blue and red light starts flashing, they will be ready to pair with any device again. With the earbuds out of the charging case, press the touch panel on both of them three times. If there is a connection problem, or the connection is lost between the earbuds, then do the following: Credits: JBL How to Manually Pair The Earbuds To Each Other? After that, a blue light will start flashing, and the pairing will be done. Step 5: Open the lid of the charging case and take the earbuds out. Step 3: Go to “Bluetooth and other devices”. Step 1: Turn on Bluetooth on the desired device. Step 3: Go to the device’s Bluetooth settings. Step 2: Turn on Bluetooth on the desired device. After that, a blue light will start flashing, and the earbuds will turn on automatically Step 1: Open the lid of the charging case and take the earbuds out. JBL Endurance Peak II Guide & Troubleshooting How to Pair The Earbuds? To iOS and Android phones
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |